An isometric render of a small outdoor event: picnic mats with seated figures, a performance area with speakers and a laptop table, and a loaded bicycle at the far end.

Take what you need

This is a kit to pull from, not a checklist to complete. Everything below is optional, and what you bring depends on what the event is for.

The full version is a laptop, an audio interface, a recorder, two MIDI keyboards, three speakers, three power banks, three lamps, a microphone and the cables to connect it all. It fits on one bicycle with no trailer, which is the constraint the list was built around.

The renders on this page come from a Blender file, which is a free download: XUSIONE SETUP A (ZIP, 6 MB). Open it to measure what actually fits on a rack, try a different layout, or strip it back to the pieces you own. It is also on the Free Assets page.

If you add only one thing to a phone and a speaker, make it a wired connection. It removes a whole category of Bluetooth problems at once (dropouts, latency, the speaker pairing with somebody else's phone) and it costs a cable.

Power

Modern low-power laptops go a long way on their own battery. A current MacBook Air will manage ten hours or more with the screen dimmed, and an M1 still runs a loaded session (Max/MSP, a soft synth or two) for five or six — both figures on the internal battery alone, before a bank is plugged in. That five or six is what the rest of the power budget is built around.

The example setup is built for roughly twelve hours, from an M1 MacBook Air, two 192 Wh Dometic PLB15 banks and a 40,000 mAh brick (about 148 Wh). One of the big banks is the laptop's and covers it alone: at ten to fifteen watts that is more than twelve hours of charging on top of the internal battery, so the laptop is never the thing that runs out. The second big bank goes to the speakers, which is the part that does run out. The brick takes the phone, the recorder and the powered hub, and the lamps stay on their own batteries or gas.

Work out your own figure from the hours you want and what your machine actually draws, and leave a margin, because no bank delivers quite what is printed on the side.

Choose the laptop for battery life, not specs. A low-power machine such as a MacBook Air stretches a bank much further than a hungry one, and that sets the power budget for every other device on the list.

A few less obvious points:

  • Check the output, not just the capacity. A bank with a big capacity figure is no use for a laptop if its ports cannot deliver enough wattage. Look for USB-C Power Delivery at a rating that matches your laptop's charger, and confirm it before buying.
  • Consider a unit that takes solar, and that charges while in use. A panel input turns a bank into something that is topped up through the day rather than only before and after, which is worth most on the one feeding the speakers. The pairing is what matters: the PLB15 can be charged and discharged at the same time, so a panel can be filling it while the speakers draw from it. Plenty of banks do one but not the other, so it is worth confirming before buying.
  • Cold weather costs capacity. Batteries deliver less when cold. Outdoors in winter, assume noticeably less than the rating, and keep the banks in an insulated bag rather than on the ground.
  • Charge everything the night before. That includes the things that are easy to forget: the speakers, any keyboards that are not bus-powered, the recorder, the phone you are using as a clock.
  • Label the banks. Three identical bricks, two of them flat, is a puzzle you do not want to solve in the dark. Tape and a marker are enough.
  • Air travel. Airlines restrict high-capacity banks, and both sizes here are past the usual 100 Wh carry-on limit. This only matters if the setup is going further than the bike can take it, but it is worth knowing before you reach the gate.

Power in XusioMart » — power banks and power stations

Speakers and cables

Close view of the performance area: a laptop on a small folding table, two long speakers, red power banks and cable runs across the ground.

Two speakers out front, computer and interface on a low table, power banks kept together and off the grass.

Battery-powered speakers are the part of this list that has improved most in recent years. Wattage is not what decides the choice: a wired input — a 3.5 mm jack or a line input of some kind — comes first, then battery life, weather resistance and price, and then whether it keeps playing while fed from an external supply. Plenty of otherwise good speakers are Bluetooth only, or go quiet the moment they are plugged in, and either omission makes them awkward for live use.

The setup above is built around the Sony ULT Field 5, which meets all of that. Sony rates it at 25 hours of playback; at the volume an outdoor crowd needs it will be far less, and six hours on a single charge is a safe assumption. That is a reserve rather than a deadline, because one of the big banks is the speakers' and feeds them while they play. A speaker that cannot take power while playing has to be swapped out instead, which is a different kind of afternoon. Any speaker meeting those criteria works the same way.

The example carries three of them: two facing the audience, and a third as a monitor for whoever is playing — or simply as more volume when the space turns out bigger than expected.

Why wired matters:

  • No latency. Bluetooth adds a delay between keypress and sound, which makes playing live unpleasant and anything synced to video unworkable.
  • No dropouts. A crowd is a lot of phones all competing for the same radio band.
  • No pairing. Nobody's phone can take the speaker over mid-set.
  • Better battery life on the speaker, as a side effect.

Buy audio cables longer than seems sensible. Speaker placement is set by where people end up standing, not by where the table is, and a cable that is three metres short forces a rethink of the whole layout. Run cable along the edges rather than through the middle, and tape or weight it down so a foot catching it does not pull a speaker over.

On placement: get the speakers off the ground if possible, point them across the crowd rather than into it, and space them wider than feels natural. Two speakers set well apart cover a space better than two side by side playing louder.

PA in XusioMart » — speakers, wired and Bluetooth  ·  Interconnects » — cable and splitters

The computer

The laptop runs the apps, and three accessories make it usable outdoors.

A hood

A laptop screen outdoors is close to unreadable. Daylight washes the image out, and a dark interface turns the panel into a mirror showing the sky and your own face. A hood, bought or made from stiff card and gaffer tape, is the cheapest item on this list and the one most likely to be missing when you need it.

It also helps to switch the apps to a light theme outdoors. A pale interface stays legible in conditions where a dark one has already become a mirror.

A stand or small folding table

A laptop on the ground means working on hands and knees, with grit in the keyboard. Anything that raises it to a workable height will do, as long as it folds flat enough to strap to a bike. The same surface carries the interface and the recorder, so a little extra area is worth the weight.

A USB hub, and every cable

A thin laptop may have only two ports, and the setup has an interface, two keyboards, a recorder and a phone to charge. A powered hub solves that. Pack the full set of device cables rather than guessing which you will need: the one left at home is always the one with no substitute in a field.

Audio interface and recorder

Both of these are nice to have rather than required. A laptop's own headphone output into a speaker works perfectly well.

An audio interface earns its place when there is more than one source to balance, such as a mic and the computer or two performers. It also gives you better converters and a proper headphone output for cueing, and it puts physical knobs between the computer and the speakers, which helps when the laptop screen is unreadable in the sun.

The spare inputs do the same job for audio that the hub's spare ports do for controllers: whatever someone arrives with — a phone, a guitar, a small synth — goes into a channel of its own and sits in the mix alongside everything else, with its own level. Without an interface a second source means unplugging the first.

A portable recorder, fed from the interface's outputs, captures the set as it happened. It is the item people most regret skipping: a recording costs almost nothing to make, cannot be made afterwards, and doubles as source material for everything you post later.

The Tascam DR-05X is the recommendation. It records to a card with no computer involved, and it takes power two ways: a pair of AA cells, good for something like seventeen hours, or USB from a bank, which is Tascam's own suggestion for long sessions. The cells are the reason it is here — the recording is the one thing that cannot be made again afterwards, and on AAs it does not touch the power budget at all, with a spare set costing less than anything else that buys another few hours.

Tascam in XusioMart » — handheld recorders  ·  Tech » — laptops and tablets

Keyboards and control

The example uses two keyboards, which suits the widest range of situations, but what you carry depends entirely on your instrumentation. Two of the same thing stays flexible: either one can take whatever a player needs it to, and nothing in the setup depends on which one somebody sat down at.

A laptop setup with a hub also means anyone turning up with their own controller can plug it in. Whatever ports the interface and the recorder are not using are free, and a class-compliant controller needs no driver and nothing configured, so it takes seconds — worth keeping a spare long cable for.

Three things to check before buying:

  • Bus power. A keyboard powered over USB needs no battery and no adapter to lose or forget to charge.
  • Size against the bike. Weight climbs faster than key count: a slim 25-key is around 0.2 kg against a little over two for a 49-key, so the example setup spends roughly 4.4 kg on keyboards alone. That is the deliberate trade — four octaves each, at the cost of the heaviest items on the bike after the speakers. Drop to 25 or 37 keys and most of that weight goes away.
  • Class-compliant USB. Controllers that need a manufacturer's driver are a poor fit for browser-based apps. Anything that appears as a standard MIDI device works everywhere.

Buy long USB cables for them, 3 to 5 metres. The keyboards want to be where people are and the laptop wants to be on the table, and a standard one-metre cable ties the two together and forces a bad layout.

If the computer in the setup is a tablet, check first: external MIDI hardware does not work on iPhone or iPad in any browser. The apps still run and still make sound; only physical controllers fail. Full details in Running the Apps on a Phone

To let the audience join in from their own phones, bring QR codes linking to MMOFX. Laminated cards are easy to hand out and survive damp grass and spilled drinks. A larger sign, mounted near the table or the seating, catches anyone who arrives late.

MIDI in XusioMart » — keyboards, controllers and sequencers

Microphone

One microphone and a 5-metre cable. That covers introductions, announcements, a guest reading something, and any moment when what needs saying has to reach past the front row.

For outdoor use with speakers in the same space, a dynamic microphone is the straightforward choice: it rejects more of what it is not pointed at, which keeps feedback under control. Condensers are more detailed but much more trouble in an open space with live speakers.

The cable wants to be long enough that the mic can leave the table. A microphone tethered to the equipment is a microphone nobody walks up to.

Input in XusioMart » — microphones  ·  Stands » — mic and speaker stands

Light

Three lamps, mostly for practical reasons: so the gear can be found at the end, so people can see each other once it is dark, and so packing down does not happen by phone torch.

Whatever you use should carry its own power or need none. Lamps with internal batteries are the straightforward option. Gas, oil or candle lanterns also work and leave the electrical budget untouched, but take obvious care with an open flame near fabric, dry grass and people sitting close.

Do not run lighting from the power banks. Light is the easiest thing on the list to supply independently, and every bit of bank capacity spent on it is taken from the laptop.

A warm colour and a diffuse output do more for a space than anything bright and directional. Skip lighting entirely for an indoor space that already has light, or for an event that finishes before dark. It is the first thing to cut when the load is too heavy.

One lamp on the table, one on the seating and one spare is plenty.

Ambiance in XusioMart » — lighting and the things that mark a space

Packing it

An isometric render of a loaded bicycle with panniers, speakers strapped to a rear rack and a front rack, and the remaining gear laid out beside it.

Front rack, rear rack, two panniers and a crate. Everything else in the list is laid out to the right.

The load divides into three kinds of thing, and they want different treatment:

  • Long and light — speakers, lamps, keyboards. These strap flat across the racks, and being bulky rather than heavy they can ride high.
  • Small and heavy — power banks, interface, recorder. These go low in the panniers, as close to the axles as possible. Weight carried high is what makes a loaded bike feel unmanageable.
  • Fragile and flat — the laptop, the hood, the folding table. These travel in a padded bag, packed so that nothing can land on them.

Cables are their own problem. Loose cable in a pannier becomes one knot by arrival. Coil each one, band it, and keep them all in a single bag so a missing one is obvious at pack-down. Cable is what most often gets left behind in the grass.

Three habits worth building:

  • Do a dry run at home. Load the bike, ride ten minutes, unload and set everything up. Most problems show up in that first run, at home, where they are easy to fix.
  • Load in reverse order of setup. What you need first (the table, the laptop, the power) goes on last, so it comes off first.
  • Keep a small spares bag. Gaffer tape, zip ties, a 3.5 mm adapter, a spare USB cable, a multi-tool. It weighs very little and will save an event sooner or later.

Weather is the other half of packing. Battery-powered speakers are often weather-resistant; laptops and power banks are not. A couple of plastic bags folded in a pocket cost nothing and turn a shower from the end of the event into an inconvenience.

Food and warmth

None of this is gear, but all of it affects how long people stay. This guide assumes guests bring their own food, drink and something to sit on. Providing food and drink yourself is not required, and catering is beyond its scope.

  • Food and drink. Bring enough for yourself first, because setting up, playing and packing down is real work. Anything shared on top of that changes the feel of the whole event. BatchWiz can scale quantities once the numbers go beyond a guess.
  • Blankets and mats. The cheapest improvement available. People stand for a while and sit for much longer, and the ground is colder than it looks. A couple of spares cover anyone who forgets.
  • Incense, or anything else that marks the space. A scent or a visible boundary tells people where the event is, which matters in an open space with no walls to do that job.

Relaxation in XusioMart » — blankets, mats and seating  ·  Bar »

Merch table

If there is something to sell or give away, give it its own surface away from the equipment table. Cash and cables should not share a space.

For payments, a QR code on a phone is enough. Printing it and taping it to the table beats holding up a screen in the sun.

Furniture » — tables for the merch table

Splitting the load

The full setup fits on one bike, but it is still a lot for one person. Anyone willing to help makes it far easier, and they do not need to know anything about the gear: two bikes carry it comfortably, one person sets up sound while the other handles seating and food, and pack-down takes half as long at the point when energy is lowest.

It also means nobody has to leave the equipment unattended just to fetch water or find a toilet.

Everything in this guide still works solo, though. Bring your own food, take less gear, and accept that the first few events will be clumsy. An imperfect event that happens beats a perfect one that never does.

The full list

For copying into a packing list. Items marked optional are genuinely optional.

QtyItemNotes
1LaptopLow power draw over high specification
1Laptop hoodOr card and tape
1Stand or folding mini tableMust fold flat
1Audio interfaceOptional
1USB hub + all device cablesPowered hub preferred
1Portable recorderOptional; fed from the interface
3High-capacity power banksTwo 192 Wh (one laptop, one speakers) and one 40,000 mAh brick (phone, recorder, hub)
1–3Battery-powered speakersWired input required, and must play while charging; fed from a bank
1–3Long audio cablesLonger than seems necessary
2MIDI keyboards49-key in the example; bus-powered, class-compliant
2Long USB cables3–5 m
1MicrophoneDynamic, for feedback rejection
1Microphone cable5 m
3LampsInternal battery or gas; never off the banks
1Spares bagTape, ties, adapters, multi-tool
—QR cards and signsLink to MMOFX; laminated cards to hand out, larger signs to mount
—Food, drink, blanketsBring your own; guests do the same

What the renders show, for reference: an M1 MacBook Air, two M-Audio Keystation 49 MK3 keyboards, three Sony ULT Field 5 speakers, two Dometic PLB15 banks alongside a 40,000 mAh brick, and a Tascam DR-05X. None of it is a requirement — the criteria in each section are what matter, and equivalents work the same way.

Everything in this list, sourced across eight regions

Open XusioMart